Fridge parts we repair and replace

Fridge thermostat replacement and sensor repairs

A fridge that freezes the milk, never switches off or will not start cooling may have a faulty thermostat or sensor. We test the whole circuit, fit the correct part for your model and check it before we leave.

  • 25 years' experience5,000+ fridges repaired
  • 300+ five-star reviewsFrom Gauteng customers
  • Open 24/7With you in about 1 hour
  • 6-month warrantyOn repairs and regassing

Fridge thermostat replacement fixes a fridge that freezes food, runs without stopping or never starts cooling because the part that senses the temperature has failed. Simpler fridges use a mechanical thermostat behind a dial, while many newer fridges, especially those with a display, use electronic sensors read by a control board. Check the setting with a thermometer first, because a wrong setting can look exactly like a faulty part.

Two ways a fridge controls its temperature

Mechanical thermostats

A mechanical thermostat is a switch behind the dial with a thin, sealed capillary tube filled with gas. The tube’s tip is clipped to the cooling plate, or sits in the cold air stream on some frost-free models. As the tip warms, the gas pressure rises and pushes a small bellows that closes the switch and starts the compressor, the pump that moves the refrigerant. As it cools, the switch opens again.

Three things commonly go wrong:

  • A tip knocked out of its clip feels the wrong temperature.
  • A tube that cracks and loses its gas cannot sense the fridge warming, so the compressor usually never starts.
  • Contacts that wear, burn or stick closed give erratic cooling or a compressor that never stops.

On many static (manual defrost) fridge-freezers, one thermostat in the fridge section controls both compartments, so the dial changes the freezer too. Some frost-free fridges add a second dial for a damper, a flap that lets cold air from the freezer into the fridge.

Electronic sensors

Most fridges with a display use thermistors, small sensors whose electrical resistance changes with temperature, read by the control board. A broken sensor or wire often sets a code, such as Er rS or Er FS on an LG fridge, or E1 or E2 on many Hisense fridges. A sensor that drifts may set no code, so the board cools too much or too little.

Fridge thermostat settings and what the numbers mean

A fridge section should sit between 3 and 5°C, and a freezer at −18°C or colder. Dial numbers are steps of cooling power, not degrees, and on most fridges a higher number is colder. On many dials, 0 is off. Start in the middle and move one step at a time. Fast-cool modes that catch people out are explained in our fridge freezing food guide.

How to check the temperature yourself

  1. Put a fridge thermometer in a cup of water on a middle shelf. Water warms and cools as slowly as food, so opening the door barely moves the reading.
  2. In the freezer, slide a second thermometer between two frozen packs.
  3. Read both first thing in the morning, before any door is opened.
  4. If a reading is still wrong a full day after a one-step change, and the seal and coils are fine, suspect the thermostat or a sensor.

Signs your fridge thermostat is not working

What you notice Thermostat or sensor likely if Check these too
Food freezes, compressor never stops it keeps running with the dial turned to off Fast-cool mode, a damper stuck open
Warm and silent, light on the dial gives no click when turned from off to cold Start relay, overload protector, defrost timer, compressor
Warm, compressor runs all day rarely, because a running compressor shows it is calling for cold Low gas, dirty coils, a failed fan
Temperatures swing for no clear reason the seal is sound and the setting has not changed A packed fridge, doors opened often, a hot or cold room

If the dial clicks but the compressor only hums and clicks off, suspect the start relay or the compressor. A fridge that runs all day but stays warm is covered under fridge not cooling.

Other temperature parts with similar symptoms

  • The defrost thermostat or sensor. On frost-free fridges, it sits on the evaporator and ends each defrost once the ice has melted. If it fails, the evaporator can ice up, as our ice build-up guide explains.
  • The damper. Stuck open, it freezes the fridge section. Stuck closed, it leaves a warm fridge with a cold freezer.
  • The control board. If every sensor tests correctly and the fridge still ignores them, see control board repairs.
  • The door seal. A leaking door seal makes the fridge run longer and frost up.

What a fridge thermostat replacement involves

We repair all major fridge brands. The job has three steps:

  1. Test the circuit. We check the setting, test the thermostat switch and inspect the capillary tube and its clip. On electronic fridges, we read any code, measure each sensor against the maker’s chart at a known temperature and check the wiring.
  2. Fit the correct part for the model. Thermostats differ in temperature range and tube length, and sensors in resistance values, so a lookalike part can leave the fridge too warm or too cold. Common thermostats can often be fitted on the first visit, and if a model-specific part must be ordered, we give you the lead time.
  3. Set it and check it. We route the tube or sensor the way the manufacturer did, then check that the compressor responds to the setting and the temperatures begin to fall.

A thermostat or sensor is usually a much smaller repair than a compressor, and you get a clear price before work starts. If your thermometer readings stay wrong, book a thermostat repair.

FAQ

Fridge thermostat replacement: questions

Can a fridge thermostat be repaired, or does it have to be replaced?

A mechanical thermostat is sealed, so if its switch or capillary tube fails, the whole thermostat is replaced. A failed sensor is replaced too. Sometimes the part is fine and the fault is a loose plug or a chafed wire, which we repair instead.

Should I turn my fridge to the coldest setting in summer?

Usually not. The thermostat reacts to the temperature inside, so in hot weather the compressor just runs longer to hold the same setting, while the coldest setting can freeze food at the back. If a thermometer shows the fridge above 5°C, go one step colder, then unplug it and brush the dust off the condenser coils.

What is a thermistor in a fridge?

A thermistor is a small temperature sensor, usually sealed in a plastic tip on a wire. As it gets colder its resistance rises, which the control board reads as a temperature. Many electronic fridges have one per compartment and one on the evaporator for defrosting, and some have one for the room temperature.

Why does my fridge display show a different temperature from my thermometer?

On many fridges, the display shows the temperature you set, not a live reading, and air near the door is warmer than at the back. A degree or two of difference is normal. If a thermometer in water is still well off after a day, a sensor may be faulty.

Need fridge thermostat replacement?

Book a technician to your door anywhere in Gauteng. You get a clear price before any work starts.

WhatsApp us