Fridge parts we repair and replace

Fridge control board repair and replacement

A dead display, an error code or a fridge that stops after a power cut can point to the control board, but the fault can be elsewhere. We test first, then replace a faulty board with the correct one for your model.

  • 25 years' experience5,000+ fridges repaired
  • 300+ five-star reviewsFrom Gauteng customers
  • Open 24/7With you in about 1 hour
  • 6-month warrantyOn repairs and regassing

A fridge control board repair starts by proving the board is at fault. A dead display, an error code or a compressor that will not run can come from a failed board, but a faulty sensor, door switch or loose plug can cause the same symptoms. When the board has failed, we replace it with the correct one for your model.

The boards in a modern fridge

Electronic fridges, usually the ones with a display, are run by a control board, or PCB (printed circuit board). Depending on the model, there may be one or more:

  • Main or power board. It takes mains power, reads the sensors and switches the compressor, fans, heaters and lights.
  • Display board. The control panel shows temperatures and codes and passes your button presses to the main board. On door displays, its wires usually run through the top hinge.
  • Inverter board. On inverter fridges, it controls the compressor’s speed, either as a separate board or as part of the main board.

Many fridges with a plain dial and no display have no board at all.

Signs of a control board fault

  • A dead or flickering display, missing segments or buttons that do nothing, while the socket works.
  • A code that shows the boards have lost contact, such as 88 88 or PC ER on a Samsung fridge, Er CO on an LG fridge or E6 on many Hisense fridges.
  • Temperatures that wander although the sensors test correctly.
  • Fans or a compressor that will not run, although the parts themselves are fine.
  • Rapid, repeated clicking from the main board, which can be a relay (an electrically worked switch) chattering on a failing board.

A click every few minutes from the compressor is usually the start relay or overload protector instead, covered under compressor replacement. If the fridge is completely dead, start with the plug, socket and DB board, which our fridge not turning on guide covers step by step.

Why fridge boards fail in Gauteng

  • Power cuts. When the supply returns, the voltage can spike or dip for a moment, and the board’s power supply takes the hit each time, as our Johannesburg page on power cuts explains.
  • Lightning. In the summer storm season, a strike near overhead lines can push a surge into nearby homes, as our Centurion page describes.
  • Moisture. Water from a blocked defrost drain, a leaking dispenser line or a damp garage can corrode a board or its plugs. If water collects in your fridge, see our guide to a fridge leaking water.
  • Age. Heat slowly wears out the components over the years, so an older board is more likely to fail at the next surge.

How a fridge control board repair works

Ruling out the parts that mimic a board fault

A board acts on what its inputs tell it, so one bad input can make a healthy board look faulty:

  • Sensors. A failed temperature or defrost sensor feeds the board a false reading, as our thermostat and sensor page explains.
  • Door switches. Many frost-free fridges stop the fan while a door is open, so a switch that wrongly reports the door open can leave the fan off and set off the door alarm.
  • Wiring and plugs. A chafed wire in a door hinge, or a plug shaken loose in a move, can trigger a communication code.
  • Fans and heaters. A seized fan or a shorted heater can set a code, and a shorted part can burn out the board that powers it. Unless that part is found, a new board can fail the same way.

So we read the code and any stored faults, test the sensors, switches and buttons, and check that the board powers the compressor, fans, heaters and damper when it should. Only when the inputs are right and the outputs are not do we replace the board.

Replacing the board

We repair all major fridge brands. Main and display boards are usually model-specific, so a board often has to be ordered, and we tell you the lead time when we quote. Once it is fitted, we set it up for the model where needed, then test the compressor, fans, heaters and display and check the temperatures.

While you wait for a board, keep the doors shut as much as you can. Food in the fridge should stay cold for about 4 hours, and frozen food for about 48 hours in a full freezer or 24 in a half-full one. For a longer wait, move perishables to a cooler box with ice. If in doubt, throw it out.

Protecting the new board

  • Fit a surge protector with a switch-on delay. It sits between the wall socket and the fridge, absorbs everyday spikes and waits a few minutes after the power returns before passing it on.
  • Switch off at the wall in power cuts and before storms. Without a delay protector, switch the fridge off when the power goes and on again a few minutes after it returns. Before a storm arrives, switch off and pull out the plug, never while it is overhead.

If your fridge shows a code, book a repair for your error code and send a photo of the display and the rating plate.

FAQ

Fridge control board repairs: questions

Why are the buttons on my fridge display not working?

Check for a lock first. Many fridges have a control lock or child lock, usually cleared by holding the lock button for a few seconds, as your manual explains. If the buttons still do nothing, the display board or its wiring to the main board may be faulty, and we test both.

Where is the control board in my fridge?

On most fridges, the main board sits behind a cover on top of the cabinet or low down at the back, near the compressor, and the display board sits behind the control panel. Do not open either cover yourself, because parts of the main board carry mains voltage whenever the fridge is plugged in.

How long does it take to get a new fridge control board?

It depends on the model and on what suppliers have in stock. We confirm the exact board from the model number on the rating plate and the part number printed on the old board, and give you the lead time with the quote. A photo of the rating plate sent when you book speeds this up.

Is it worth replacing the control board on an older fridge?

Often, yes, if the compressor and the rest of the cooling system are sound. Buying new makes more sense when the repair would cost over half the price of a similar new fridge, or when a fridge over about 10 to 12 years old also needs a compressor. You get the price first.

Need fridge control board repairs?

Book a technician to your door anywhere in Gauteng. You get a clear price before any work starts.

WhatsApp us