Most side by side fridge repairs come down to four things: ice blocking the airflow, a door that no longer seals, a water fault or the electronics. Usually the repair is done in your kitchen, with the fridge left in its place.
How these big fridges keep cold
Side-by-side (American-style), French-door and multi-door fridges are almost all frost-free. On many models, a fan blows air over a single evaporator (the cooling coil) behind the freezer’s back panel. In a side-by-side, part of that air passes through the centre wall into the fridge side. In a French-door fridge, a duct carries it up from the freezer drawer. A damper (a small flap) decides how much gets through. Some models, including Samsung fridges with Twin Cooling Plus, have a separate evaporator and fan for each compartment instead.
To stop the coil icing up, a heater melts the frost at intervals, and the water runs down a drain to a tray at the bottom, where it evaporates. If the fan, the damper or the defrost system fails, the fridge section usually warms up while the freezer stays cold, as our guide to a warm fridge with a cold freezer explains.
Common side-by-side and French-door faults
Ice behind the panels and fans that scrape
When the defrost heater, its sensor or the control fails, frost builds into solid ice around the evaporator. The first sign is often a scraping or ticking sound as the fan blade catches on the ice. Switching off for a day melts the ice and stops the noise, but it returns within days or weeks until the faulty part is replaced.
Error codes point to a place, not a cause
Samsung’s 21E and 22E and LG’s Er FF and Er rF are fan errors. They often mean ice is blocking the fan, so the real fault is in the defrost system. On most Hisense fridges, E1 or E2 points to a temperature sensor. Our Samsung, LG and Hisense pages list more codes, including Samsung’s OF OF, which is demo mode rather than a fault.
Heavy doors that drop out of line
Bottles and dispenser parts make these doors heavy, and over the years a plastic bush in the hinge wears or the hinge works loose, so the door sags. If one door sits lower than the other, or the gap between them is uneven from top to bottom, the seal is probably not closing at one corner. Frost near the top of the freezer and an ice maker that keeps freezing up often start this way.
We adjust the door height at the hinge, replace worn hinge parts and level the fridge so it leans back slightly, which helps the doors swing shut. A torn or flattened seal needs door seal replacement.
The centre flap on French-door fridges
One of the two fridge doors, usually the left, has a hinged flap called a mullion along its inside edge. It folds in when that door opens, and a guide at the top of the cabinet turns it out across the gap as the door closes, so both door seals have something to close against. Inside the flap, a small anti-condensation heater keeps it just warm enough to stop moisture forming.
When the heater or its wiring fails, the flap sweats and drips, and frost can grow along it. When the spring or the guide breaks, the flap may not turn into place, leaving a gap between the doors.
Water where it should not be
A blocked or frozen drain leaves a sheet of ice on the freezer floor, or water under the crisper drawers on models with a drain in the fridge section. A fridge that leans forward can tip defrost water out at the front. On dispenser models, the water filter housing and the supply line can leak too, as our guide to a fridge leaking water explains.
Inverter compressors, ice makers and electronics
Many side-by-sides have an inverter compressor run by a board, and a board fault can stop a compressor that is fine, as our page on inverter fridges explains. Ice makers and dispensers add valves, filters and water lines, or on many models sold here a tank you fill by hand, as our guide to ice maker and water dispenser repairs explains.
The main board takes the full mains supply, which leaves it most exposed to surges when the power returns, so a surge protector with a switch-on delay is worth fitting. If the display went blank or showed a code after the power came back, tell us when you book, and see our page on control board repairs.
Side by side fridge repairs we do on site
We repair all major fridge brands. The evaporator fan, sensors, heaters, dampers, hinges, seals and the centre flap are reached from the front, with the fridge where it stands. To reach the compressor, the condenser fan or a board at the back, we ease the fridge forward a little, checking first that a plumbed water line has enough slack. Fridge regassing is done on site too, with the leak repaired first.
Many repairs are finished on the first visit, and if a model-specific part such as a control board must be ordered, we tell you the lead time. When you book a repair, send a photo of the rating plate and any code on the display.