Fridge and freezer types we repair

Integrated fridge repairs that protect your cabinets

Running warm, icing up, dripping behind the plinth or a door that will not line up? We repair integrated and built-under fridges across Gauteng, with care for the cabinetry around them.

  • 25 years' experience5,000+ fridges repaired
  • 300+ five-star reviewsFrom Gauteng customers
  • Open 24/7With you in about 1 hour
  • 6-month warrantyOn repairs and regassing

Integrated fridge repairs often start outside the fridge. A built-in fridge lives in a cabinet housing, so blocked vents, a dropped cabinet door or a leak hidden behind the plinth cause problems a freestanding fridge does not have. We check the housing as well as the fridge, and many repairs are done without taking it out.

Built-in, or just standing in an alcove?

An integrated fridge or fridge-freezer has no finished door of its own. It is screwed into a cabinet, the housing, behind a door that matches the kitchen, and an integrated built-under fridge does the same beneath the worktop. A freestanding fridge has its own finished door and sides, and even in a gap between cupboards it needs the open space its manual asks for, as our Fourways guide to tight fridge gaps explains.

Why the plinth and the top vent matter

Every fridge pushes heat out through its condenser, the coil that gets warm. In a built-in fridge, cool air comes in through a vent in the plinth (the kickboard under the cabinets), rises up a channel behind the fridge and leaves through a vent at the top of the housing, like a chimney. Bosch, for example, asks for ventilation openings of at least 200 cm² behind and below its built-in fridges. Built-under models, with a worktop above them, usually breathe through the plinth alone.

Block either end and the heat stays in the housing. The compressor runs far longer, the cabinets around the fridge feel warm and the food is not cold enough.

  • Vacuum the plinth vent every few months, because dust and pet hair collect there.
  • During a renovation, do not close off the top vent with a bulkhead or swap a vented plinth for a solid one.
  • When fitting a new fridge, follow the niche size and ventilation requirements in its own installation instructions, not the old fridge’s.

Door fixings and the seal

The cabinet door is joined to the fridge door in one of two ways. With door-on-door fitting, sometimes called a fixed door, the cabinet door is screwed straight onto the fridge door, so the fridge’s own hinges carry its weight. With a sliding door, the cabinet door hangs on cabinet hinges and slides along a rail on the fridge door as it opens.

Both drift out of line: a heavy cabinet door pulls door-on-door hinges down, and the brackets of a sliding door work loose in the chipboard. The fridge door then stays slightly open or sits crooked, and moist air gets past the seal. We adjust the hinges, re-fix loose brackets in solid board and fit a new seal if needed, as our page on door seal replacement explains.

Common integrated fridge repairs

Built-in fridge not cooling or never switching off

Ventilation is the first suspect, then the causes any fridge can have: a fan, a thermostat or sensor, or a gas leak. Our guide to a fridge not cooling explains how we tell them apart.

Ice on the back wall

Many integrated fridges cool through a plate in the back wall that frosts while the compressor runs and clears when it rests. Thick ice there points to a door that has dropped out of line, or to a fridge that never rests because it cannot shed its heat. Our guide to ice build-up covers the other causes.

Noise carried through the cabinets

The housing works like a sounding box. A fridge touching the side of the housing, a loose fixing screw or a worn compressor mounting turns a normal hum into a buzz you hear across the kitchen, as our guide to a noisy fridge explains.

Sensors and boards

On electronic models, a sensor that reads wrongly or a failed control board leaves the fridge too cold, too warm or dead, as our page on control board repairs explains.

Hidden leaks under the cabinets

Defrost water runs from a channel at the back of the fridge through a tube into a tray on top of the compressor, where it evaporates. If the tube came loose during fitting or the tray is cracked, the water drips into the base of the housing or behind the plinth, out of sight. A swollen plinth or cabinet base, a damp floor at the kickboard or a musty smell are the usual signs, and our guide to a fridge leaking water covers other leaks.

Taking a fridge out of its housing

A new compressor, a gas leak in the pipework or a hidden drain fault usually means the fridge has to come out. We protect the floor and the cabinet edges, take off the plinth, release the door fixings and the screws that hold the fridge in place, and slide it out square so it does not scrape the cabinet sides. When it goes back, we refit the brackets, realign both doors, check the seal all the way round and make sure the air path is clear.

Common parts are often fitted on the first visit, but premium European fridges use many model-specific parts. A control board, or many parts for a Miele, may have to be ordered, and we tell you the lead time before any work starts. On Bosch and Siemens fridges, the E-Nr on the rating plate lets us look up the parts that fit. We repair all major fridge brands. If you book a repair with a photo of the rating plate, we can bring the right parts.

FAQ

Built-in and integrated fridge repairs: questions

Can I put a freestanding fridge into a built-in housing?

Not as a rule. A freestanding fridge sheds heat through its back or sides and needs open space around it, while an integrated one breathes through the plinth and the top of the housing. Shut in a niche, a freestanding fridge runs hot and wears out sooner.

What size niche does an integrated fridge need?

Most European integrated fridges fit a niche about 56 cm wide, in standard heights from about 82 cm under a worktop to about 178 cm. Depth, vents and exact sizes still vary, so check the installation instructions before you buy.

Is it worth repairing an integrated fridge?

Usually. A new integrated fridge must match the niche, vents and door fixings, so repairing is often simpler. Replacing it starts to make sense if it is over about 10 to 12 years old and needs a compressor, or the repair would cost more than half as much as a comparable new one.

Why is the plinth under my integrated fridge wet?

Defrost water is probably escaping before it reaches the tray on the compressor, for example from a drain tube knocked loose when the fridge was fitted. Many plinths clip off, so look with a torch, and switch the fridge off before you reach in. If the water keeps coming back, book a repair.

Need built-in and integrated fridge repairs?

Book a technician to your door anywhere in Gauteng. You get a clear price before any work starts.

WhatsApp us