Fridge parts we repair and replace

Fridge door seal replacement at your home

A torn, flat or mouldy fridge rubber lets warm, damp air in all day, so the fridge frosts up and runs longer. We test the seal and the door, fit the right seal for your model and set the door so it closes properly.

  • 25 years' experience5,000+ fridges repaired
  • 300+ five-star reviewsFrom Gauteng customers
  • Open 24/7With you in about 1 hour
  • 6-month warrantyOn repairs and regassing

Fridge door seal replacement means removing the worn seal, fitting a new one made for your model and setting the door so the seal meets the cabinet evenly all round. Test the seal first, though. A dirty or kinked seal can often be revived, and many gaps come from a door that has dropped or a fridge that is not level.

Signs your fridge door is not sealing

The seal, which many South Africans call the fridge rubber and parts suppliers call the gasket, is usually soft PVC with a flexible magnetic strip inside that pulls it against the metal front of the cabinet. When it fails, you tend to see:

  • Splits, often starting at a corner, or flat, hard or cracked sections.
  • Black mould in the folds that returns soon after cleaning.
  • Frost, ice or condensation near the door.
  • A fridge that runs longer than it used to.
  • Soft ice cream at the front of the freezer, although a freezer that is not freezing has other causes too.
  • A door that does not stay shut.

Damp air that gets past the seal turns to frost. In a frost-free fridge it settles on the evaporator, the cooling coil behind the freezer panel, and can ice it up faster than the defrost system clears it. That is one cause of a warm fridge with a cold freezer, and our ice build-up guide explains ice in other places.

Two tests you can do in a few minutes

The paper test. Shut the door on a strip of paper or a banknote and pull it out slowly. It should drag the same everywhere, and where it slides out freely the seal is not gripping. Test three spots on each side, hinge side included, and every corner, where tears often start.

The torch test. In a dark kitchen, stand a lit torch on a shelf facing the door edge, close the door and look for light around the seal. Move it to each side in turn.

Where the gaps are tells you what is wrong:

  • A short gap at one spot, with a visible tear or flat section, points to the seal.
  • A gap that widens towards one corner usually means the door has dropped or twisted, or the fridge is not level.
  • Weak grip everywhere, with a stiff seal, means the seal has hardened with age.

Cleaning and reviving a seal

Wash the seal with a soft cloth and warm water with a little dishwashing liquid, using an old soft toothbrush for the folds. Rinse, then dry it well, folds included, because mould grows where water sits. Avoid bleach, solvents and scouring powder, which dry out and harden the seal.

A squashed or kinked section may recover if you hold a cloth wrung out in warm water against it for a few minutes, ease it into shape and close the door. Faded stains are cosmetic if the seal still grips, but mould that keeps returning means replacing it.

When the door is the problem

A new seal will not close a gap that the door itself leaves, so we check the door first:

  • Sagging hinges. Heavy door bins, children swinging on the door and loose hinge screws pull the door down over time.
  • A fridge that is not level. A fridge that leans forward lets the door drift open. Many manufacturers want the front slightly higher than the back, set with the adjustable front feet on most fridges.
  • A door that was reversed and refitted badly. A hinge pin, door stop or cover left out or fitted the wrong way round leaves the door hanging crooked.

Our Tembisa guide to a door that will not close covers these checks, and drawers or bottles that stop the door short. French-door fridges also have a hinged flap between the doors that must turn into place as the door shuts, covered on our side-by-side and French-door fridge page. On an integrated fridge, a badly set cupboard door can hold the fridge door open.

How we do a fridge door seal replacement

Push-in or screw-held. Many modern fridges have push-in seals, with a ridged strip that presses into a channel around the door: the old seal pulls out and the new one presses in, corners first. Older fridges and some current models clamp the seal under the inner door lining with screws, which we loosen to free the old seal and tighten evenly so the new one does not ripple.

Model-specific or universal. We repair all major fridge brands. A seal ordered by your fridge’s model number comes at the right size and profile, with its corners already joined. A universal seal is cut to size and its corners joined by hand, mainly for older fridges whose own seal is no longer made. Seals for many fridges can be fitted on the first visit, and if yours must be ordered, we tell you the lead time.

Fitting, shaping and checking. We warm the new seal to relax the creases from its packaging, fit it and, where needed, adjust the hinges and level the fridge. Then we repeat the paper test all round and check that the door swings shut by itself. If the seal is sound and the fridge still frosts up or never switches off, the thermostat or a temperature sensor is the next suspect.

If your seal fails the paper test, book a door seal replacement and WhatsApp us a photo of the rating plate so we can check which seal fits.

FAQ

Fridge door seal replacement: questions

Can I glue a torn fridge door rubber?

Gluing a tear rarely lasts. The seal flexes every time the door opens, so the repair pulls apart, and glue can leave a lump that stops the seal sitting flat. A torn seal is better replaced.

Why is my fridge door hard to open straight after I close it?

That usually means the seal is good. Warm air comes in while the door is open, then cools and shrinks once the door is shut, and the suction can hold the door for a minute or more. If a door that used to resist now opens with no effort, try the paper test.

What if the exact seal for my fridge is no longer made?

We look for one with the same size and profile. Failing that, a universal seal cut to fit can work, especially where screws hold the inner door lining, and we tell you before we start if that is the only option.

Will a new door seal lower my electricity bill?

It can. A leaking seal lets in warm, damp air, so the compressor runs longer and frost builds up, which makes it work harder still. How much you save depends on how bad the leak was.

Need fridge door seal replacement?

Book a technician to your door anywhere in Gauteng. You get a clear price before any work starts.

WhatsApp us