A little ice build-up in a fridge is normal on a static (manual defrost) model, which usually needs defrosting every few months. Thick ice, a fridge or freezer icing up again within days and solid ice in a frost-free freezer point to a problem: damp air getting in, a blocked or frozen drain, or a failed defrost part. The kind of ice and where it forms tell you which.
Static or frost-free? Check first
A static fridge’s cooling surface is in plain view, as a metal plate, an ice box or the back wall, so some frost is expected. A frost-free (no frost) fridge hides its cooling coil, the evaporator, behind a freezer panel and melts the frost off with a heater, so solid ice on its walls or floor points to a fault. Bosch LowFrost and Liebherr SmartFrost freezers sit in between: far less ice, but still an occasional defrost.
What the ice build-up in your fridge is telling you
Thin, even frost on the cooling plate or in the freezer
This frost build-up is normal in a static fridge or freezer, including a chest freezer, and it grows faster in humid summer weather or when the door or lid is opened often. Defrost at about 5 mm, because thicker ice insulates the plate and makes the fridge run longer.
Thick ice on the back wall of the fridge
On a static fridge the back wall frosts while the compressor runs and clears to droplets when it rests. Thick ice on the back of the fridge is not normal, and its shape is a clue:
- A ridge along the bottom, around the drain hole. The meltwater cannot drain away, so it refreezes. Clear the drain as shown in our fridge leaking water guide.
- Lumps where food or containers touch the wall. Leave a gap of a few centimetres.
- A sheet that never clears. Damp air is getting in past the seal or a door opened often, or the fridge never switches off. If food freezes too, the fridge freezing food guide explains why.
Ice on the freezer floor or under the bottom drawer
In a frost-free freezer, water from each defrost runs off the coil into a trough and out through a drain at the back, kept clear by a small heater, or by a metal strap warmed by the defrost heater. If that fails, or debris lets the drain freeze, the next meltwater spills across the floor and sets as a flat sheet of ice. It often starts at the back and can lock the bottom drawer. A full defrost clears it, but it comes back until the fault is fixed.
Frost on food and inside packets
A little frost inside packets builds up slowly in any freezer, because each swing in temperature draws moisture out of the food to refreeze in the bag. Heavy frost within a week or two usually means moisture is getting in: a seal that no longer grips, a door opened often or held ajar by a packet, or food that went in warm. Cool cooked food first, but freeze it within about two hours.
Thick frost on the back panel of a frost-free freezer
This is usually a frost-free fridge icing up because its defrost system has failed: a burnt-out defrost heater, a faulty defrost sensor or thermostat, or a timer or control board that no longer starts the cycle. Frost grows on the hidden coil until it shows on the panel and around the fan grille, and the fan may start scraping. The fridge section usually warms first, because the ice blocks its air supply (see warm fridge, cold freezer). Defrosting by hand only buys time.
Ice around the door opening
Frost along one edge or corner of the door opening means air is leaking past a torn or flattened seal, or the door has dropped out of line. On a freezer the problem feeds itself, because ice on the lip holds the door slightly open and lets in more air. A new door seal or a hinge adjustment usually fixes it.
If the ice keeps coming back, book an ice build-up repair. We repair all major fridge brands.
How to defrost a fridge or freezer safely
- Switch the fridge off and unplug it.
- Move the food to a cooler box with ice packs and keep it shut.
- Lay towels on the floor and a tray in the freezer, and empty the drip tray under a static ice box as it fills.
- Leave the doors open.
- Let the ice loosen and fall by itself, lifting loose pieces out by hand.
- Dry everything, seals included, then switch on and let it get cold before you reload.
Never chip at the ice with a knife, screwdriver or ice pick, or use a heat gun or hair dryer. The cooling plate on many static fridges is thin aluminium with gas channels inside, so one slip while chipping ice can puncture it. A puncture needs a proper fridge regas. Most newer fridges run on R600a, a flammable gas, so if you hear a hiss after a slip, keep flames, cigarettes and sparks away, open the windows for a few minutes, and only then switch off, unplug and call us.